Digi-CordComputer Cords and Cables

How do you patch the bottom an in ground fiber glass pool?

At a boy scout camp there is a pool that is from the 1940s it is in ground pool and it is very big and deep about 22ft deep it hasn’t been used till about the early 1970s and they were going to fill it in with concrete but i convinced them to not do so so we drained it the water was black and at the shallow end of the pool it was cracked in a few spots and i guess it leaks and i was wandering how to patch it up and make it sealed any cheap shortcuts the pool is fiber glass

they have an epoxy made for fiberglass. check you local hardware store

How to install a fibre patch cord in the dark

…

Belkin F2F202L0-02M 2-Meter Multimode Duplex ST-LC Fiber Patch Cable $13.27 Belkin Components is the preeminent technology leader in connectivity solutions for the puter and consumer electronics user. Producing the highest-quality cabling products has always been the key to success. Always ahead of the rest Belkin supports the latest technologies. Belkin the leader in the cable industry has the cable you need!Primary InformationNetwork Cable Type :  Network Cable Cabl…

…

Diablo Cable 2m SC/SC Duplex 9/125 Single Mode Fiber Patch Cable $10.36 Diablo Cable 9/125 fibre cables provide a low cost option for gigabit ethernet network applications. The SC connectors provide a secure locking mechanism to ensure connection reliability. Each cable is tested for optical integrity and loss prior to packaging to ensure proper data transmission. The durable rubber boots protects against damage typical in busy data racks and each end is properly labe…

Diablo Cable 50m LC/LC Duplex 9/125 Single Mode Fiber Patch Cable $59.46 Diablo Cable 9/125 fibre cables provide a low cost option for gigabit ethernet network applications. The LC jumper connector provides a secure locking mechanism to ensure connection reliability. Each cable is tested for optical integrity and loss prior to packaging to ensure proper data transmission. The durable rubber boots protects against damage typical in busy data racks and each end is proper…

Diablo Cable 5m LC/LC Duplex 9/125 Single Mode Fiber Patch Cable $11.86 Diablo Cable 9/125 fibre cables provide a low cost option for gigabit ethernet network applications. The LC jumper connector provides a secure locking mechanism to ensure connection reliability. Each cable is tested for optical integrity and loss prior to packaging to ensure proper data transmission. The durable rubber boots protects against damage typical in busy data racks and each end is proper…

Patch: Webster’s Timeline History, 1997 – 2007 $28.95 Webster’s bibliographic and event-based timelines are comprehensive in scope, covering virtually all topics, geographic locations and people. They do so from a linguistic point of view, and in the case of this book, the focus is on “Patch,” including when used in literature (e.g. all authors that might have Patch in their name). As such, this book represents the largest compilation of timeline eve…

IEC 60874-19-1 Ed. 2.0 en:2003, Connectors for optical fibres and cables – Part 19-1: Fibre optic patch cord connector type SC-PC (floating duplex) … fibre type A1a, A1b – Detail specification $110.00 Defines the requirements and quality assessment procedures for the type SC-PC (floating duplex)fibre optic patch cord connector, standard terminated on multimode fibre type A1a and A1b….

The Cloudspotter’s Guide: The Science, History, and Culture of Clouds $3.25 Now in paperback: the runaway British bestseller that has cloudspotters everywhere looking up. Where do clouds come from? Why do they look the way they do? And why have they captured the imagination of timeless artists, Romantic poets, and every kid who’s ever held a crayon? Veteran journalist and lifelong sky watcher Gavin Pretor-Pinney reveals everything there is to know about clouds, from…

StarTech.com 2m Multimode 50/125 Duplex Fiber Patch Cable LC – LC (50FIBLCLC2) $10.34 This 2m (6.6ft) LC/LC Duplex 50/125 Multimode Fiber Patch Cable provides the necessary connection between fiber networking devices for high-speed, long distance networks. Ensuring optimal data transfers and network stability, 50/125-micron cables offer nearly three times the bandwidth of 62.5/125-micron cables, so your data will be transferred at higher rates over longer distances. Each Duplex 50/…

Fibre Channel Patch Cable $33.94 Fibre Channel Patch Cable Tripp Lite’s 10-meter multimode duplex fiber optic SC/SC patch cable is manufactured from 50/125 zipcord fiber. The cable has SC connectors on each end, a PVC jacket and is FDDI and OFNR rated. Duplex multimode fiber is most commonly used in fiber and fibre channel applications. It is backward compatible with 62.5 micron fiber and built-in headroom for future applications. The cable provides higher bandwidth optimized for Gigabit and 10Gbps networks. Main FeaturesManufacturer: Tripp LiteManufacturer Part Number: N506-10MManufacturer Website Address: www.tripplite.comProduct Type: Patch Cable Multimode ExternalCable Length: 32.81ftNumber of Connectors: 4Connector Details: 2 x SC Male, 2 x SC MaleStandard Warranty: Lifetime Limited

Tripp Lite / Tripp Lite Fibre Channel Patch Cable / N506-01M $29.45 Tripp Lite – Tripp Lite Fibre Channel Patch Cable – N506-01M

Tripplite / Tripp Lite Duplex Fibre Channel Patch Cable / N516-15M $47.29 Tripplite – Tripp Lite Duplex Fibre Channel Patch Cable – N516-15M

Fibre Optic Duplex Patch Cable $42.94 Fibre Optic Duplex Patch Cable Main FeaturesManufacturer: Belkin International, IncManufacturer Part Number: F2F802L0-10MManufacturer Website Address: www.belkin.comProduct Type: Network CableCable Type: Fiber OpticCable Characteristic: Patch CableCable Length: 33ftConnector on First End: 2 x LC MaleConnector on Second End: 2 x ST MaleColor: YellowStandard Warranty: Lifetime

Duplex Fibre Channel Patch Cable $87.94 Tripp Lite’s multimode duplex fibre channel optic LC/SC patch cable is manufactured from 50/125 zipcord fiber. The cable has SC connectors on one end and LC connectors on the other. It has a PVC jacket and is FDDI and OFNR rated. Duplex multimode fiber is most commonly used in fiber and fibre channel applications. It is backward compatible with 62.5 micron fiber and built-in headroom for future applications. The cable provides higher bandwidth optimized for Gigabit and 10Gbps networks. Tripp Lite warrants this product to be free from defects in materials and workmanship for life.

Belkin Fibre Optic Duplex Patch Cable $64.99 2 x Male 2 x ST Male 33 ft 9/125 µm Offers the optimal solution for high-speed data transmission 100% tested for quality and reliability Belkin Singlemode Duplex Fiber Patch Cables are 100% tested for quality and reliability and feature Corning glass and superior construction. Belkin Belkin International, Inc F2F802L0-10M Fiber Optic Fibre Optic Duplex Patch Cable Lifetime Network Cable Patch Cable ST Yellow www.belkin.com

Tripp Lite Duplex Fibre Channel Patch Cable $28.99 118″ 2 x LC Male 2 x SC Male 50/125 µm Network Interface Card Fiber optic card requiring multimode duplex cable with LC/SC connectors Duplex Fibre Channel Patch Cable3M Duplex MMF Cable LC/SC 50/125 Fiber FDDI OFNR Number of fibers: 2 Primary coating diameter: 245+/-15 microns Primary coating material: Acrylate Secondary coating diameter: 900+/-50 microns Numeric apeture: .275 nominal Proof test level: 100,000 PSI Insertion loss testing performed on every connector (0.2db typical) and provided with cable Beveled edge on ends of glass makes insertion of plug a breeze Color coded/labeled connectors Applications: Gigabit 10Gbps networks Fiber and fibre channel installations Tripp Lite’s 3-meter multimode duplex Fibre Channel SC/LC patch cable is manufactured from 50/125 zipcord fiber. The cable has SC connectors on one end, and LC at the other, a PVC jacket, and is FDDI and OFNR rated. 50/125 Duplex multimode fiber is most commonly used in Fibre Channel applications. It is backward compatible with 62.5 micron fiber and built-in headroom for future applications. The cable provides higher bandwidth optimized for Gigabit and 10Gbps networks as well. Also available in 1, 2, 5, 10, 15, 20, 30, and 50 meter lengths. Search “N516-” to bring up all lengths. Also search “N506-” for SC-SC cables, and “N520-” for LC-LC cables. Tripp Lite warrants this product to be free from defects in materials and workmanship for life. Duplex Fibre Channel Patch Cable Fiber Optic LC Lifetime N516-03M Network Cable Orange PVC Patch Cable SC Tripp Lite www.tripplite.com

Tripp Lite Fibre Channel Patch Cable $24.99 118″ 2 x SC Male 50/125 µm FDDI OFNR Fibre Channel Patch Cable3M duplex MMF cable SC/SC 50/125 fiber Number of fibers: 2 Fiber type: all glass graded index Core diameter: two 50+/-3 microns CLAD diameter: 125+/-2 microns Primary coating diameter: 245+/-15 microns Secondary coating diameter: 900+/-50 microns Attenuation @850NM: 3.5DB/KM maximum, @1300NM: 1.0DB/KM maximum Bandwidth @850NM: 220 MHz-KM minimum, @1300NM: 600 MHz-KM minimum Numeric apeture: .275 nominal Proof test level: 100,000 PSI Insertion loss testing performed on every connector (0.2db typical) and provided with cable Beveled edge on ends of glass makes insertion of plug a breeze Tripp Lite’s 3-meter multimode duplex Fibre Channel SC/SC patch cable is manufactured from 50/125 zipcord fiber. The cable has SC connectors on each end, a PVC jacket and is FDDI and OFNR rated. 50/125 Duplex multimode fiber is most commonly used in Fibre Channel applications. It is backward compatible with 62.5 micron fiber and built-in headroom for future applications. The cable provides higher bandwidth optimized for Gigabit and 10Gbps networks as well. Also available in 1, 2, 5, 10, 15, 30, and 50 meter lengths. Search “N506-” to bring up all lengths. Also search “N516-” for SC-LC cables, and “N520-” for LC-LC cables. Tripp Lite warrants this product to be free from defects in materials and workmanship for life. Fiber Optic Fibre Channel Patch Cable Lifetime Limited N506-03M Network Cable PVC Patch Cable SC Tripp Lite www.tripplite.com

Cables To Go Fibre Optic Simplex Patch Cable $42.99 1 x LC Male 2.88 oz 32.81 ft 37729 9/125 µm Attenuation @1310 nm: 1.0 dB/km Attenuation @1550 nm: 0.75 dB/km Maximum tensile load: 100 N/cm Loaded min. bend radius: 5 cm Unloaded min. bend radius: 3 cm Crush resistance: 750 N/cm Impact resistance: 1000 cycles Flex resistance: 5000 cycles Buffer OD: 900 µm Jacket OD: 3.0 mm CMP Blue Cables To Go Fiber Optic Fibre Optic Simplex Patch Cable LC Lifetime Network Cable Patch Cable Plenum RoHS Single-mode Yes www.cablestogo.com

2-8g Fibre To 2-8g Fibre $21642.99 2-8G FIBRE TO 2-8G FIBRE

4-8g Fibre To 4-8g Fibre $25822.99 4-8G FIBRE TO 4-8G FIBRE

Gel Coat Scratch Patch Clear Gelcoat Scratch Patch $11.94 Gel Coat Scratch Patch Clear Gelcoat Scratch Patch Fibre Glass-Evercoat Gel Coat Scratch Patch – CLEAR GELCOAT SCRATCH PATCH

Gel Coat Scratch Patch White Gelcoat Scratch Patch $11.94 Gel Coat Scratch Patch White Gelcoat Scratch Patch Fibre Glass-Evercoat Gel Coat Scratch Patch – WHITE GELCOAT SCRATCH PATCH

Belkin 16-Port Network Patch Panel $107.99 16 16 x ST Fibre Channel 16-Port Network Patch Panel 1U Rack-mountable Belkin Belkin International, Inc Belkin ST/ST Fibre Optic Patch Panel is rack mountable and ideal for managing and routing fibre patch cables in the datacenter. F4P506-16 Lifetime Network Patch Panel ST www.belkin.com

Tripp Lite Fibre Channel Patch Cable 3.28ft 2 x SC 2 x SC Patch Cable Multimode Yellow N50601M $32.67 Tripp Lite s 1meter multimode duplex fibre channel SC/SC patch cable is manufactured from 50/125 zipcord fiber. The cable has SC connectors on each end a PVC jacket and is FDDI and OFNR rated. Duplex multimode fiber is most commonly used in fiber and fibre channel applications. It is backward compatible with 62.5 micron fiber and builtin headroom for future applications. The cable provides higher bandwidth optimized for Gigabit and 10Gbps networks.

Gel Coat Scratch Patch Buff White Gelcoat Scratch Patch $11.94 Gel Coat Scratch Patch Buff White Gelcoat Scratch Patch Fibre Glass-Evercoat Gel Coat Scratch Patch – BUFF WHITE GELCOAT SCRATCH PATCH

N520-152M – Tripp Lite Premium Fibre Channel Patch Cable – Lc Male – Lc Male – 498Ft – Orange $247.5 tripp Lite’s Multimode Duplex Fibre Channel Lc/lc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Lc Connectors On Each End. It Has A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. Tripp Lite Warrants This Product To Be Free From Defects In Materials And Workmanship For Life. [L50007] UPC: 037332126344 UNSPC: 26121607 11L x 11W x 6.5H 3.3 LB 0.46 Cubes

N506-02M – Tripp Lite Fibre Channel Patch Cable – Sc Male – Sc Male – 2M – Orange $24.87 tripp Lite’s 2-meter Multimode Duplex Fibre Channel Sc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On Each End, A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. [C18287] UPC: 037332119452 UNSPC: 26121607 8L x 5.25W x 0.25H 0.12 LB 0.01 Cubes

N506-50M – Tripp Lite Duplex Fibre Channel Patch Cable – Sc – Sc – 164.04Ft $70.71 tripp Lite’s 50-meter Multimode Duplex Fibre Channel Sc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On Each End, A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. [C18291] UPC: 037332119599 UNSPC: 26121607 8L x 8W x 2.5H 1.45 LB 0.13 Cubes

N506-01M – Tripp Lite Fibre Channel Patch Cable – Sc Male – Sc Male – 3.28Ft – Yellow $20.72 tripp Lite’s 1-meter Multimode Duplex Fibre Channel Sc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On Each End, A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. [N50601M] UPC: 037332119438 UNSPC: 26121607 6L x 6W x 0.25H 0.1 LB 0.02 Cubes

N520-02M – Tripp Lite Duplex Fibre Channel Patch Cable – Lc Male – Lc Male – 6.56Ft $34.39 tripp Lite’s Multimode Duplex Fibre Channel Lc/lc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Lc Connectors On Each End. It Has A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. Tripp Lite Warrants This Product To Be Free From Defects In Materials And Workmanship For Life. [N52002M] UPC: 037332119513 UNSPC: 26121607 9.5L x 7W x 0.5H 0.05 LB 0 Cubes

N520-15M – Tripp Lite Duplex Fibre Channel Patch Cable – Lc Male – Lc Male – 49.21Ft $51.49 tripp Lite’s Multimode Duplex Fibre Channel Lc/lc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Lc Connectors On Each End. It Has A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. Tripp Lite Warrants This Product To Be Free From Defects In Materials And Workmanship For Life. [N52015M] UPC: 037332119490 UNSPC: 26121607 7.5L x 5W x 0.75H 0.24 LB 0.01 Cubes

N516-10M – Tripp Lite Duplex Fibre Channel Patch Cable – Lc Male – Sc Male – 32.81Ft $39.8 tripp Lite’s Multimode Duplex Fibre Channel Optic Lc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On One End And Lc Connectors On The Other. It Has A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. Tripp Lite Warrants This Product To Be Free From Defects In Materials And Workmanship For Life. [372859] UPC: 037332116963 UNSPC: 26121607 9.75L x 7W x 0.5H 0.15 LB 0.03 Cubes

N516-05M – Tripp Lite Duplex Fibre Channel Patch Cable – Lc Male – Sc Male – 16.4Ft $31.72 tripp Lite’s Multimode Duplex Fibre Channel Optic Lc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On One End And Lc Connectors On The Other. It Has A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. Tripp Lite Warrants This Product To Be Free From Defects In Materials And Workmanship For Life. [C18294] UPC: 037332119568 UNSPC: 26121607 6.2L x 4.8W x 0.4H 0.1 LB 0.01 Cubes

N516-15M – Tripp Lite Duplex Fibre Channel Patch Cable – Lc Male – Sc Male – 49.21Ft $44.16 tripp Lite’s Multimode Duplex Fibre Channel Optic Lc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On One End And Lc Connectors On The Other. It Has A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. Tripp Lite Warrants This Product To Be Free From Defects In Materials And Workmanship For Life. [C18295] UPC: 037332119551 UNSPC: 26121607 9L x 6W x 0.75H 0.2 LB 1 Cubes

N516-30M – Tripp Lite Duplex Fibre Channel Patch Cable – Lc Male – Sc Male – 98.43Ft $52.13 tripp Lite’s Multimode Duplex Fibre Channel Optic Lc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On One End And Lc Connectors On The Other. It Has A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. Tripp Lite Warrants This Product To Be Free From Defects In Materials And Workmanship For Life. [C18296] UPC: 037332119544 UNSPC: 26121607 10.5L x 8W x 1.5H 0.42 LB 0.03 Cubes

N516-50M – Tripp Lite Duplex Fibre Channel Patch Cable – Lc Male – Sc Male – 164.04Ft $80.17 tripp Lite’s Multimode Duplex Fibre Channel Optic Lc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On One End And Lc Connectors On The Other. It Has A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. Tripp Lite Warrants This Product To Be Free From Defects In Materials And Workmanship For Life. [989293] UPC: 037332119537 UNSPC: 26121607 13L x 10W x 2.5H 0.7 LB 0.07 Cubes

Tripp Lite Duplex Fibre Channel Patch Cable 164.04ft 2 x SC 2 x SC Cable Multimode N50650M $100.42 Tripp Lite s 50meter multimode duplex fibre channel SC/SC patch cable is manufactured from 50/125 zipcord fiber. The cable has SC connectors on each end a PVC jacket and is FDDI and OFNR rated. Duplex multimode fiber is most commonly used in fiber and fibre channel applications. It is backward compatible with 62.5 micron fiber and builtin headroom for future applications. The cable provides higher bandwidth optimized for Gigabit and 10Gbps networks.

N506-03M – Tripp Lite Fibre Channel Patch Cable – Sc Male – Sc Male – 9.84Ft $24.8 tripp Lite’s 3-meter Multimode Duplex Fiber Optic Sc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On Each End, A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. [N50603M] UPC: 037332117212 UNSPC: 26121607 9.75L x 7W x 0.25H 0.15 LB 0.02 Cubes

N506-10M – Tripp Lite Fibre Channel Patch Cable – Sc Male – Sc Male – 32.81Ft $34.46 tripp Lite’s 10-meter Multimode Duplex Fiber Optic Sc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On Each End, A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. [372849] UPC: 037332116956 UNSPC: 26121607 9L x 6.25W x 1H 0.38 LB 0.04 Cubes

N506-05M – Tripp Lite Fibre Channel Patch Cable – Sc Male – Sc Male – 16.4Ft – Yellow $28.98 tripp Lite’s 5-meter Multimode Duplex Fiber Channel Sc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On Each End, A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. [C18288] UPC: 037332118936 UNSPC: 26121607 9L x 6W x 0.5H 0.2 LB 0.01 Cubes

N506-15M – Tripp Lite Duplex Fibre Channel Patch Cable – Sc Male – Sc Male – 49.21Ft $40.9 tripp Lite’s Multimode Duplex Fiber Channel Sc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On Each End, A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. Tripp Lite Warrants This Product To Be Free From Defects In Materials And Workmanship For Life. [C18289] UPC: 037332119612 UNSPC: 26121607 10L x 8W x 1H 0.48 LB 0.06 Cubes

N506-30M – Tripp Lite Fibre Channel Patch Cable – Sc Male – Sc Male – 98.43Ft – Yellow $56.15 tripp Lite’s 30-meter Multimode Duplex Fiber Channel Sc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On Each End, A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. [C18290] UPC: 037332119582 UNSPC: 26121607 9.75L x 1.25W x 12H 0.9 LB 0.1 Cubes

N520-25M – Tripp Lite Duplex Fibre Channel Patch Cable – Lc Male – Lc Male – 82.02Ft $61.43 tripp Lite’s Multimode Duplex Fiber Optic Lc/lc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Lc Connectors On Each End. It Has A Pvc Jacket And Is Fddi And Ofnr Rated. Duplex Multimode Fiber Is Most Commonly Used In Fiber And Fibre Channel Applications. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. The Cable Provides Higher Bandwidth Optimized For Gigabit And 10gbps Networks. Tripp Lite Warrants This Product To Be Free From Defects In Materials And Workmanship For Life. [1040082] UPC: 037332123596 UNSPC: 26121607 5L x 5W x 0.01H 0.6 LB 0.03 Cubes

Match N Patch Gel Coat Repair Kit Match’n Patch Gelcoat Repair Kit $46.94 Match N Patch Gel Coat Repair Kit Match’n Patch Gelcoat Repair Kit Fibre Glass-Evercoat Match N Patch Gel Coat Repair Kit – MATCH’N PATCH GELCOAT REPAIR KIT

F4P507-16 – Belkin 16-Port Network Patch Panel – 16 X Sc $114.96 Belkin Sc/sc Fibre Optic Patch Panel is Rack Mountable And Ideal For Managing And Routing Fibre Patch Cables in The Datacenter. [N07415] UPC: 722868639955 UNSPC: 43223309 22.1L x 3.9W x 2.9H 1.25 LB

Patch $10 Patch

Fibre $4.99 We believe it is important to preserve what makes music special, and make it easy to craft listening experiences. At MOG, browse millions songs and play them instantly. Or just turn on radio where you can stop and replay songs. You can also create playlists for any occasion, and even download songs to your mobile. We are dedicated to employing the cleanest but most powerful technology so you can enjoy music as much as ever.

3M Multimode Duplex 50/125 Fibre Channel Patch Cable $29.99 Higher bandwidth optimized for gigabit and 10Gbps networks

1m Multimode Duplex LC/SC (50µ/125) Fibre Channel Patch Cable $24.99 For use with any fiber optic hardware or NIC card requiring multimode duplex cable with LC/SC connectors

30ft Duplex MMF 50/125 SC-SC Patch Cable $29.99 Tripp Lite’s 9-meter multimode duplex Fibre Channel SC/SC patch cable is manufactured from 50/125 zipcord fiber.

Cisco FDDI Fibre Module (Fibre SAS) WSX2841 $80.45 Cisco FDDI Fibre Module (Fibre SAS) WSX2841

Duplex Fiber Patch Cable $27.94 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

F2F802L0-10M – Belkin Fibre Optic Duplex Patch Cable – Lc Male – St Male – 33Ft – Yellow $51.75 belkin Singlemode Duplex Fiber Patch Cables Are 100% Tested For Quality And Reliability And Feature Corning Glass And Superior Construction. [1757844] UPC: 722868585955 UNSPC: 26121607 11.42L x 8.07W x 0.79H 0.1 LB 0.04 Cubes

Tripp Lite Duplex Fibre Channel Patch Cable 9.84ft 2 x LC 2 x SC Patch Cable Multimode Orange N51603M $41.8 Tripp Lite s 3meter multimode duplex fiber optic LC/SC patch cable is manufactured from 50/125 zipcord fiber. The cable has SC connectors on one end and LC connectors on the other. It has a PVC jacket and is FDDI and OFNR rated. It is backward compatible with 62.5 micron fiber and builtin headroom for future applications.

F4P506-16 – Belkin 16-Port Network Patch Panel – 16 X St $114.96 Belkin St/st Fibre Optic Patch Panel is Rack Mountable And Ideal For Managing And Routing Fibre Patch Cables in The Datacenter. [N07414] UPC: 722868639948 UNSPC: 43223309 22L x 3.9W x 2.9H 1.2 LB 1 Cubes

Ultra Fibre Supplement Caplets $15.49 Ultra Fibre Supplement Caplets

Carbon Fibre Centre Diff.Plate $16.74 Carbon Fibre Centre Diff.Plate

Carbon Fibre Radio Tray $30.96 Carbon Fibre Radio Tray

Carbon Fibre Steering $26.6 Carbon Fibre Steering

CARBON FIBRE BLADE $35 CARBON FIBRE BLADE

Carbon fibre tail blade $14.5 Carbon fibre tail blade

Carbon fibre paddle $14.5 Carbon fibre paddle

Carbon fibre tail boom $16 Carbon fibre tail boom

High Fibre Cooking $10.36 High Fibre Cooking

Tandberg Fibre Channel 871134 $4902.75 Tandberg Fibre Channel 871134

HP Fibre Channel BL544A $8080.06 HP Fibre Channel BL544A

Quantum Fibre Channel LSC1SUTDGL4HA $6810.74 Quantum Fibre Channel LSC1SUTDGL4HA

A Practical Guide to Fibre Science $80 A Practical Guide to Fibre Science

N516-03M – Tripp Lite Duplex Fibre Channel Patch Cable – Lc Male – Sc Male – 9.84Ft – Orange $28.98 tripp Lite’s 3-meter Multimode Duplex Fiber Optic Lc/sc Patch Cable Is Manufactured From 50/125 Zipcord Fiber. The Cable Has Sc Connectors On One End And Lc Connectors On The Other. It Has A Pvc Jacket And Is Fddi And Ofnr Rated. It Is Backward Compatible With 62.5 Micron Fiber And Built-in Headroom For Future Applications. [N51603M] UPC: 037332117229 UNSPC: 26121607 9L x 6.5W x 0.25H 0.1 LB 0.02 Cubes

carbon fibre battery tray $3.5 carbon fibre battery tray EXI-32114

Cables To Go Q-Series Network Patch Panel $26.99 1 lb 12-Port Q-Series Network Patch Panel was designed with legacy installations in mind. Each adapter is pre-loaded with a feed-thru mating sleeve which serves as the intermediate connection between the backbone and your patch cable. Simply select you connector type, then plug-and-play. 31101 5.13″ x 1.13″ Black Cables To Go Lifetime Network Patch Panel Q Q-Series Network Patch Panel RoHS ST ST Fibre Channel Yes www.cablestogo.com

Duplex Fiber Optic Patch Cable $97.94 Tripp Lite’s multimode duplex fibre channel optic LC/LC patch cable is manufactured from 50/125 zipcord fiber. The cable has LC connectors on each end. It has a PVC jacket and is FDDI and OFNR rated. Duplex multimode fiber is most commonly used in fiber and fibre channel applications. It is backward compatible with 62.5 micron fiber and built-in headroom for future applications. The cable provides higher bandwidth optimized for Gigabit and 10Gbps networks. Tripp Lite warrants this product to be free from defects in materials and workmanship for life.

Fiber Optic Patch Cable $39.94 Tripp Lite’s 10-meter multimode duplex fiber optic LC/ST patch cable is manufactured from 50/125 zipcord fiber. The cable has LC connectors on one end, and ST connectors on the other. It has a PVC jacket and is FDDI and OFNR rated. Duplex multimode fiber is most commonly used in fiber and Fibre Channel applications. It is backward compatible with 62.5 micron fiber and built-in headroom for future applications. The cable provides higher bandwidth optimized for Gigabit and 10Gbps networks. Main FeaturesManufacturer: Tripp LiteManufacturer Part Number: N518-10MManufacturer Website Address: www.tripplite.comProduct Type: Patch Cable Multimode ExternalCable Length: 32.81ftNumber of Connectors: 4Connector Details: 2 x LC, 2 x STStandard Warranty: Lifetime

23ft (7m) Duplex Multimode Fiber Optic 50/125 Patch Cable – LC/LC $38.99 Tripp Lite’s 7-meter multimode duplex Fibre Channel optic LC/LC patch cable is manufactured from 50/125 zipcord fiber.

12M (40-ft.) Duplex MMF 50/125 Patch Cable (LC/LC) $43.99 This 12-meter multimode duplex Fibre Channel optic LC/LC patch cable is manufactured from 50/125 zipcord fiber. The cable has LC connectors on each end. It has a PVC jacket an

30M Duplex MMF 50/125 Plenum Patch Cable LC/LC 100ft $241.99 Tripp Lite’s 30-meter multimode duplex Fibre Channel optic LC/LC patch cable is manufactured from 50/125 zipcord fiber. The cable has LC connectors on each end. It has a PLENU

Tripp Lite Patch Cable – 164 Ft. Each $70.72 Manufacturer: Tripp Lite. Each. Tripp Lite’s 50-meter multimode duplex fibre channel SC/SC patch cable is manufactured from 50/125 zipcord fiber. The cable has SC connectors on each end, a PVC jacket and is FDDI and OFNR rated. Duplex multimode fiber is m

F4P509-16 – Belkin 16-Port Network Patch Panel – 16 X Lc $131.38 Belkin Lc/lc Fibre Optic Patch Panel is Rack Mountable And Ideal For Managing And Routing Fiber Patch Cables in The Datacenter. [2011447] UPC: 722868639979 UNSPC: 43223309 22.1L x 3.9W x 2.9H 1.15 LB 1 Cubes

Cables To Go USA-Made LC/LC Duplex 62.5/125 Multimode Fiber Patch Cable – Patch Cable – 16.4 Ft. Each $51.94 Manufacturer: Cables To Go. Each. These high-quality LC to LC Fiber Optic Patch Jumpers are designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The

Fiber Optic Duplex Patch Cable $45.94 Cables To Go offers high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality.

21625 – Cables To Go Fibre Optic Duplex Patch Cable – Lc Male – Sc Male – 49.21Ft – Aqua $89.03 [20190S] UPC: 757120216254 UNSPC: 26121607 8.2L x 6.1W x 0.4H 0.55 LB 1 Cubes

F2F402Ll-300 – Belkin Fibre Optic Duplex Patch Cable – Lc Male – Lc Male – 300Ft – Orange $271.2 [F2F402LL300] UPC: 722868663196 UNSPC: 26121607 9.84L x 9.84W x 2.16H 4.5 LB 1 Cubes

21624 – Cables To Go Fibre Optic Duplex Patch Cable – Lc Male – Sc Male – 32.81Ft – Aqua $77.48 [2257447] UPC: 757120216247 UNSPC: 26121607 11.5L x 6.8W x 0.8H 0.4 LB 0.06 Cubes

33444 – Cables To Go Fibre Optic Simplex Patch Cable – Lc Male – Lc Male – 32.81Ft – Black $27.98 [2257229] UPC: 757120334446 UNSPC: 26121607 6.69L x 8.27W x 0.39H 0.18 LB 1 Cubes

21639 – Cables To Go Fibre Optic Duplex Patch Cable – St Male – St Male – 32.81Ft – Aqua $64.86 [2257477] UPC: 757120216391 UNSPC: 26121607 7.5L x 6W x 0.75H 0.26 LB

21640 – Cables To Go Fibre Optic Duplex Patch Cable – St Male – St Male – 49.21Ft – Aqua $76.22 [2257478] UPC: 757120216407 UNSPC: 26121607 7L x 6W x 1H 0.36 LB

21654 – Cables To Go Fibre Optic Duplex Patch Cable – St Male – Sc Male – 32.81Ft – Aqua $67.68 [2257470] UPC: 757120216544 UNSPC: 26121607 5.5L x 6.5W x 1H 0.26 LB

21655 – Cables To Go Fibre Optic Duplex Patch Cable – St Male – Sc Male – 49.21Ft – Aqua $76.22 [2257471] UPC: 757120216551 UNSPC: 26121607 6.5L x 6W x 0.5H 0.36 LB

21684 – Cables To Go Fibre Optic Duplex Patch Cable – Lc Male – St Male – 32.81Ft – Aqua $71.61 [2257462] UPC: 757120216841 UNSPC: 26121607 8L x 8W x 1H 0.26 LB

21685 – Cables To Go Fibre Optic Duplex Patch Cable – Lc Male – St Male – 49.21Ft – Aqua $81.87 [2257463] UPC: 757120216858 UNSPC: 26121607 7.5L x 6.5W x 0.5H 0.36 LB

21669 – Cables To Go Fibre Optic Duplex Patch Cable – Sc Male – Sc Male – 32.81Ft – Aqua $67.68 [2257455] UPC: 757120216698 UNSPC: 26121607 7L x 6.5W x 0.75H 0.26 LB 1 Cubes

FIBRE CHANNEL CABLE DSUB9/HSSDC8 2 $78.99 FIBRE CHANNEL CABLE DSUB9/HSSDC8 2

FIBRE CHANNEL CABLE DSUB9/HSSDC8 1 $217.99 FIBRE CHANNEL CABLE DSUB9/HSSDC8 1

IBM 44X1921 Fibre Channel Switch $6673.5 IBM 44X1921 Fibre Channel Switch

Forerunnerle 155Mbps Fibre PCI Card $92.24 Forerunnerle 155Mbps Fibre PCI Card

HP Fibre Channel, iSCSI AW568A $12916.98 HP Fibre Channel, iSCSI AW568A

Compaq Fibre Channel Tape Controller $168.32 Compaq Fibre Channel Tape Controller

Pad,Gold Fibre Retro,Iy $6.99 PAD,GOLD FIBRE RETRO,IVY

1M DUPLEX FIBRE LC/LC MMF $23.99 Cables to Go LC/LC Duplex 50/125 Multimode Fiber Patch Cable – Patch cable – LC multi-mode (M) – LC multi-mode (M) – 3.3 ft – fiber optic – 50 / 125 micron – blue

5M FIBER OPTIC/FIBRE CHANNEL $47.99 Tripp Lite – Patch cable – ST multi-mode (M) – LC multi-mode (M) – 16.4 ft – fiber optic – 50 / 125 micron – orange

Belkin 16-Port Network Patch Panel – 16 x LC $214.99 Belkin LC/LC Fibre Optic Patch Panel is rack mountable and ideal for managing and routing fiber patch cables in the datacenter.

Belkin Fibre Optic Duplex Patch Cable – LC Male – ST Male – 33ft – Yellow $249.99 Belkin Singlemode Duplex Fiber Patch Cables are 100% tested for quality and reliability and feature Corning glass and superior construction.

Belkin Fibre Optic Duplex Patch Cable – LC Male – ST Male – 33ft – Yellow $157.95 Belkin Singlemode Duplex Fiber Patch Cables are 100% tested for quality and reliability and feature Corning glass and superior construction.

Cables To Go Duplex Fiber Optic Patch Cable – LC Male – LC Male – 32.81ft $29.38 Get the performance you demand at a price that makes sense with multicolored 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with todays narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Color-coded connector keys available in red blue green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer material: PVC. Buffer OD: 900 m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Blue. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Duplex Fiber Optic Patch Cable – LC Male Network – LC Male Network – 29.53ft – Orange $34.44 We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Duplex Fiber Optic Patch Cable – LC Male Network – ST Male Network – 13.12ft – Orange $22.02 Get the performance you demand at a price that makes sense with 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with todays narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) ST. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Duplex Fiber Patch Cable – LC Male – LC Male – 16.4ft – Orange $52.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – LC Male – 19.69ft – Orange $55.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – LC Male – 22.97ft – Orange $59.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – LC Male – 3.28ft – Orange $37.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – LC Male – 32.81ft – Orange $65.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – LC Male – 49.21ft – Orange $84.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – LC Male – 65.62ft – Orange $94.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – LC Male – 9.84ft – Orange $45.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – SC Male – 16.4ft – Orange $39.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – SC Male – 19.69ft – Orange $42.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – SC Male – 22.97ft – Orange $44.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – SC Male – 26.25ft – Orange $30 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – SC Male – 39.37ft – Orange $38 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – SC Male – 6.56ft – Orange $32.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – LC Male – SC Male – 65.62ft – Orange $74.99 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – SC Male – SC Male – 13.12ft – Orange $21.5 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – SC Male – SC Male – 26.25ft – Orange $28.75 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – SC Male – SC Male – 32.81ft – Orange $30.75 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Duplex Fiber Patch Cable – SC Male – SC Male – 65.62ft – Orange $58.75 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with 62.5/125 applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol.

Cables To Go Fiber Optic Duplex Cable – LC Network – LC Network – 13.12ft – Orange $29.25 We offer high-quality62.5/125 Low-Smoke Zero-Halogen (LSZH) Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. LSZH jackets are composed of materials that lessen the emmissions of smoke and halogens when the cable is exposed to extreme temperatures. This reduces the amount of harmful toxic and corrosive gases that cabling made with plastic materials would otherwise emit into the air during combustion. This construction makes LSZH cables ideal for use where the protection of people and equipment from harmful corrosive gasses is absolutely critical. Custom lengths are available. Features: Low-Smoke Zero-Halogen jackets provide protection from toxic and corrosive gasses in poorly ventilated spaces and other areas where it is most critical. Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – LC Network – LC Network – 19.69ft – Orange $33 We offer high-quality62.5/125 Low-Smoke Zero-Halogen (LSZH) Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. LSZH jackets are composed of materials that lessen the emmissions of smoke and halogens when the cable is exposed to extreme temperatures. This reduces the amount of harmful toxic and corrosive gases that cabling made with plastic materials would otherwise emit into the air during combustion. This construction makes LSZH cables ideal for use where the protection of people and equipment from harmful corrosive gasses is absolutely critical. Custom lengths are available. Features: Low-Smoke Zero-Halogen jackets provide protection from toxic and corrosive gasses in poorly ventilated spaces and other areas where it is most critical. Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – LC Network – SC Network – 29.53ft – Orange $41.25 We offer high-quality62.5/125 Low-Smoke Zero-Halogen (LSZH) Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. LSZH jackets are composed of materials that lessen the emmissions of smoke and halogens when the cable is exposed to extreme temperatures. This reduces the amount of harmful toxic and corrosive gases that cabling made with plastic materials would otherwise emit into the air during combustion. This construction makes LSZH cables ideal for use where the protection of people and equipment from harmful corrosive gasses is absolutely critical. Custom lengths are available. Features: Low-Smoke Zero-Halogen jackets provide protection from toxic and corrosive gasses in poorly ventilated spaces and other areas where it is most critical. Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) SC. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – LC Network – ST Network – 13.12ft – Orange $25.75 We offer high-quality62.5/125 Low-Smoke Zero-Halogen (LSZH) Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. LSZH jackets are composed of materials that lessen the emmissions of smoke and halogens when the cable is exposed to extreme temperatures. This reduces the amount of harmful toxic and corrosive gases that cabling made with plastic materials would otherwise emit into the air during combustion. This construction makes LSZH cables ideal for use where the protection of people and equipment from harmful corrosive gasses is absolutely critical. Custom lengths are available. Features: Low-Smoke Zero-Halogen jackets provide protection from toxic and corrosive gasses in poorly ventilated spaces and other areas where it is most critical. Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) ST. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – Plenum-Rated – LC Network – LC Network – 19.69ft – Orange $34.75 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with todays narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – Plenum-Rated – LC Network – LC Network – 22.97ft – Orange $36 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with todays narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – Plenum-Rated – LC Network – SC Network – 13.12ft – Orange $31.75 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with today s narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) SC. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – Plenum-Rated – LC Network – SC Network – 19.69ft – Orange $35.75 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with todays narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) SC. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – Plenum-Rated – LC Network – ST Network – 22.97ft – Orange $36.75 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with todays narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) ST. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – Plenum-Rated – ST Network – ST Network – 19.69ft – Orange $33.25 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with today s narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) ST to (2) ST. Buffer material: PVC. Buffer OD: 900 m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – ST Network – LC Network – 19.69ft – Orange $26.49 Get the performance you demand at a price that makes sense with 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with today s narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) ST. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – ST Network – SC Network – 13.12ft – Orange $24 Get the performance you demand at a price that makes sense with 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with today s narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) ST to (2) SC. Buffer OD: 900 m. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – ST Network – SC Network – 19.69ft – Orange $26.75 Get the performance you demand at a price that makes sense with 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with today s narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) ST to (2) SC. Buffer OD: 900 m. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – ST Network – ST Network – 13.12ft – Orange $24 We offer high-quality50/125 Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) ST to (2) ST. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Cable – ST Network – ST Network – 22.97ft – Orange $30.5 We offer high-quality62.5/125 Low-Smoke Zero-Halogen (LSZH) Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. LSZH jackets are composed of materials that lessen the emmissions of smoke and halogens when the cable is exposed to extreme temperatures. This reduces the amount of harmful toxic and corrosive gases that cabling made with plastic materials would otherwise emit into the air during combustion. This construction makes LSZH cables ideal for use where the protection of people and equipment from harmful corrosive gasses is absolutely critical. Custom lengths are available. Features: Low-Smoke Zero-Halogen jackets provide protection from toxic and corrosive gasses in poorly ventilated spaces and other areas where it is most critical. Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) ST to (2) ST. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Multimode Patch Cable – LC Male – LC Male – 16.4ft – Blue $27 Get the performance you demand at a price that makes sense with multicolored 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with today s narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Color-coded connector keys available in red blue green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer material: PVC. Buffer OD: 900 m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Blue. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Multimode Patch Cable – LC Male – LC Male – 9.84ft – Blue $21.77 Get the performance you demand at a price that makes sense with multicolored 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with todays narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Color-coded connector keys available in red blue green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer material: PVC. Buffer OD: 900 m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Blue. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Multimode Patch Cable – LC Male – ST Male – 6.56ft – Black $30.03 Get the performance you demand at a price that makes sense with multicolored 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Color-coded connector keys available in red, blue, green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) ST. Buffer material: PVC. Buffer OD: 900 ?m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Black. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Multimode Patch Cable – Plenum – LC Male – LC Male – 49.21ft – Orange $84.99 We offer high-quality Plenum-Rated LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Multimode Patch Cable – Plenum – LC Male – SC Male – 98.43ft – Orange $72.5 We offer high-quality Plenum-Rated LC to SC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Connector: LC Male to SC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Multimode Patch Cable with Clips – LC Male – MT-RJ Male – 19.69ft – Orange $30.75 We offer high-quality LC to MTRJ Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts durin cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available. Connector: LC Male to MTRJ Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Multimode Patch Cable with Clips – LC Male – MT-RJ Male – 22.97ft – Orange $32.5 We offer high-quality LC to MTRJ Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts durin cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available. Connector: LC Male to MTRJ Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – (LSZH) – LC Male – SC Male – 65.62ft – Orange $64.5 We offer high-quality62.5/125 Low-Smoke Zero-Halogen (LSZH) Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. LSZH jackets are composed of materials that lessen the emmissions of smoke and halogens when the cable is exposed to extreme temperatures. This reduces the amount of harmful toxic and corrosive gases that cabling made with plastic materials would otherwise emit into the air during combustion. This construction makes LSZH cables ideal for use where the protection of people and equipment from harmful corrosive gasses is absolutely critical. Custom lengths are available. Features: Low-Smoke Zero-Halogen jackets provide protection from toxic and corrosive gasses in poorly ventilated spaces and other areas where it is most critical. Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) SC. Buffer OD: 900 ?m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – (LSZH) – SC Male – SC Male – 98.43ft – Orange $80.75 We offer high-quality62.5/125 Low-Smoke Zero-Halogen (LSZH) Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. LSZH jackets are composed of materials that lessen the emmissions of smoke and halogens when the cable is exposed to extreme temperatures. This reduces the amount of harmful toxic and corrosive gases that cabling made with plastic materials would otherwise emit into the air during combustion. This construction makes LSZH cables ideal for use where the protection of people and equipment from harmful corrosive gasses is absolutely critical. Custom lengths are available. Features: Low-Smoke Zero-Halogen jackets provide protection from toxic and corrosive gasses in poorly ventilated spaces and other areas where it is most critical. Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) SC to (2) SC. Buffer OD: 900 ?m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – (LSZH) – SC Male – ST Male – 65.62ft – Orange $61.75 We offer high-quality62.5/125 Low-Smoke Zero-Halogen (LSZH) Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. LSZH jackets are composed of materials that lessen the emmissions of smoke and halogens when the cable is exposed to extreme temperatures. This reduces the amount of harmful toxic and corrosive gases that cabling made with plastic materials would otherwise emit into the air during combustion. This construction makes LSZH cables ideal for use where the protection of people and equipment from harmful corrosive gasses is absolutely critical. Custom lengths are available. Features: Low-Smoke Zero-Halogen jackets provide protection from toxic and corrosive gasses in poorly ventilated spaces and other areas where it is most critical. Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) ST to (2) SC. Buffer OD: 900 ?m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – (Plenum) – LC Male – LC Male – 16.4ft – Orange $33.75 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 ?m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – (Plenum) – LC Male – LC Male – 32.81ft – Orange $40.25 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 ?m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – (Plenum) – LC Male – LC Male – 6.56ft – Orange $34.17 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 ?m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – (Plenum) – LC Male – LC Male – 65.62ft – Orange $62.61 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 ?m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – (Plenum) – LC Male – LC Male – 65.62ft – Orange $104.99 We offer high-quality Plenum-Rated LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – (Plenum) – LC Male – LC Male – 98.43ft – Orange $80.75 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 ?m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – (Plenum) – LC Male – LC Male – 98.43ft – Orange $66.5 We offer high-quality Plenum-Rated LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – (Plenum) – ST Male – SC Male – 3.28ft – Orange $27.25 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) ST to (2) SC. Buffer material: PVC. Buffer OD: 900 ?m. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – (Plenum) – ST Male – ST Male – 65.62ft – Orange $66 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) ST to (2) ST. Buffer material: PVC. Buffer OD: 900 ?m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – 16.4ft – Blue $26 Get the performance you demand at a price that makes sense with multicolored 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Color-coded connector keys available in red, blue, green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) ST to (2) SC. Buffer material: PVC. Buffer OD: 900 ?m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Blue. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – 16.4ft – Red $27 Get the performance you demand at a price that makes sense with multicolored 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with todays narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Color-coded connector keys available in red, blue, green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer material: PVC. Buffer OD: 900 ?m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Red. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 13.12ft – Orange $28.25 We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 16.4ft $30.75 We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 16.4ft – Green $20.5 Our multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 16.4ft – Green $25.25 We offer high-quality plenum-rated LC to LC fiber optic patch jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 16.4ft – Orange $31.25 We offer high-quality62.5/125 Low-Smoke Zero-Halogen (LSZH) Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. LSZH jackets are composed of materials that lessen the emmissions of smoke and halogens when the cable is exposed to extreme temperatures. This reduces the amount of harmful toxic and corrosive gases that cabling made with plastic materials would otherwise emit into the air during combustion. This construction makes LSZH cables ideal for use where the protection of people and equipment from harmful corrosive gasses is absolutely critical. Custom lengths are available. Features: Low-Smoke Zero-Halogen jackets provide protection from toxic and corrosive gasses in poorly ventilated spaces and other areas where it is most critical. Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 ?m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 16.4ft – Red $19.97 Our multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 26.25ft – Orange $34 We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 3.28ft – Black $16.5 Our multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 3.28ft – Black $21.25 Get the performance you demand at a price that makes sense with multicolored 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with today s narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Color-coded connector keys available in red blue green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer material: PVC. Buffer OD: 900 m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Black. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 3.28ft – Black $20.25 We offer high-quality plenum-rated LC to LC fiber optic patch jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 3.28ft – Blue $16.5 Our multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red, blue, green and black. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 3.28ft – Blue $27.81 We offer high-quality plenum-rated LC to LC fiber optic patch jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 3.28ft – Green $24.75 We offer high-quality plenum-rated LC to LC fiber optic patch jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red, blue, green and black. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 3.28ft – Orange $59.99 We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 3.28ft – Red $16.5 Our multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 32.81ft – Black $24.5 Our multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red, blue, green and black. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 32.81ft – Blue $24.5 Our multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 32.81ft – Blue $28.83 We offer high-quality plenum-rated LC to LC fiber optic patch jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 32.81ft – Green $24.5 Our multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 32.81ft – Orange $37.25 We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 32.81ft – Orange $31.5 We offer high-quality Plenum-Rated LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 32.81ft – Red $31.5 We offer high-quality plenum-rated LC to LC fiber optic patch jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red, blue, green and black. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Black $42.99 Get the performance you demand at a price that makes sense with multicolored 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Color-coded connector keys available in red, blue, green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer material: PVC. Buffer OD: 900 ?m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Black. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Blue $22.25 We offer high-quality plenum-rated LC to LC fiber optic patch jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Blue $21.75 Get the performance you demand at a price that makes sense with multicolored 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with todays narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Color-coded connector keys available in red, blue, green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer material: PVC. Buffer OD: 900 ?m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Blue. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Blue $18 Our multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red, blue, green and black. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Green $18 Our multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. We offer high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red, blue, green and black. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Green $22.25 We offer high-quality plenum-rated LC to LC fiber optic patch jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Green $21.75 Get the performance you demand at a price that makes sense with multicolored 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with todays narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available – just give us a call at 800-506-9607. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Color-coded connector keys available in red blue green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer material: PVC. Buffer OD: 900 m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Green. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Orange $25.25 We offer high-quality62.5/125 Low-Smoke Zero-Halogen (LSZH) Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. These Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, ATM and Gigabit Ethernet applications. Use to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. Each cable is individually 100% optically inspected and tested for insertion loss and quality. LSZH jackets are composed of materials that lessen the emmissions of smoke and halogens when the cable is exposed to extreme temperatures. This reduces the amount of harmful toxic and corrosive gases that cabling made with plastic materials would otherwise emit into the air during combustion. This construction makes LSZH cables ideal for use where the protection of people and equipment from harmful corrosive gasses is absolutely critical. Custom lengths are available. Features: Low-Smoke Zero-Halogen jackets provide protection from toxic and corrosive gasses in poorly ventilated spaces and other areas where it is most critical. Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 ?m. Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Orange $40.06 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer material: PVC. Buffer OD: 900 ?m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Orange $30.11 We offer high-quality Plenum-Rated LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. Custom lengths are available – just give us a call at 800-506-9607. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Red $25.32 Get the performance you demand at a price that makes sense with Plenum-Rated 50/125 Multimode Fiber Patch Cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber but are still cost effective. Perfect for use with today s narrower aperture components they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet Fibre Channel Infiniband ATM and Internet Protocol. These cables provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. Color-coded connector keys available in red blue green and black. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer OD: 900 m. Jacket OD: 3.0 mm. Jacket color: Red. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 6.56ft – Red $22.25 We offer high-quality plenum-rated LC to LC fiber optic patch jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red, blue, green and black. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small, rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet, Equipment Room, Work Area. Includes LC clips.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 65.62ft – Orange $74.99 Cables To Go offers high-quality LC to LC Fiber Optic Patch Jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet, Fibre Channel, Infiniband, ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area, and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects, interconnects, and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls, strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 65.62ft – Orange $74.25 Get the performance you demand at a price that makes sense with 50/125 multimode fiber patch cords from Cables To Go. They provide higher bandwidth and transmission rates and support longer distances with lower loss than 62.5/125 fiber, but are still cost effective. Perfect for use with today’s narrower aperture components, they are fully compatible with multimode applications. 50/125 multimode patch cords from Cables To Go are well-suited for protocols such as Ethernet, Fibre Channel, Infiniband, ATM, and Internet Protocol. Custom lengths are available. Features: Fully compatible with multimode fiber applications. A Cost effective solution that provides lower loss and higher bandwidth supporting longer distances. Perfect for use in Gigabit Ethernet applications. Lifetime warranty against defects of materials and workmanship. Specifications: Connectors: (2) LC to (2) LC. Buffer material: PVC. Buffer OD: 900 ?m. Jacket material: PVC (OFNR-rated). Jacket OD: 3.0 mm. Jacket color: Orange. Attenuation @850 nm: 3.75 dB/km. Attenuation @1310 nm: 1.5 dB/km. Min. bandwidth @850 nm: 160 kHz/km. Min. bandwidth @1310 nm: 500 kHz/km. Maximum tensile load: 100 N/cm. Loaded min. bend radius: 5 cm. Unloaded min. bend radius: 3 cm. Crush resistance: 750 N/cm. Impact resistance: 1000 cycles. Flex resistance: 5000 cycles.

Cables To Go Fiber Optic Duplex Patch Cable – LC Male – LC Male – 9.84ft – Black $31.07 We offer high-quality plenum-rated LC to LC fiber optic patch jumpers designed to meet or exceed industry specifications. LC Fiber Patch Jumpers are perfect for Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. The small LC connectors satisfy the need for higher port density both in the telecom room and the work area and offer twice the port density of traditional SC and ST fiber connectors. Fiber patch cords are used to connect fiber optic equipment to fiber optic cross-connects interconnects and information outlets. The LC cable with latch clip design gives each connection greater durability in resisting pulls strains and impacts during cabling installs and maintenance. Each cable is individually 100% optically inspected and tested for insertion loss and quality. These cables also provide the fire protection required to run within walls and air plenums without the need for conduit. These multicolored fiber optic patch cables enable you to quickly identify various applications present in your fiber distribution system. The connectors on each end are color-coded for easy identification in a congested patch field. Custom lengths are available. Connector: LC Male to LC Male. Fiber Size: 62.5/125 micron. Type: Multimode; Duplex. Features: Color-coded connector keys available in red blue green and black. CMP rated cable jacket provides the fire protection required to run these cables within walls and air plenums without the need for conduit. RJ style latch in a connector body half the size of a conventional SC. Small rugged design. LC connector is easy to engage and disengage featuring a telephone jack style release mechanism. Latch design prevents the plug from snagging when jumper cables are being routed. Immune to electrical interference. Application: Fast Ethernet Fibre Channel Infiniband ATM and Gigabit Ethernet. Subsystem: Telecommunications Closet Equipment Room Work Area. Includes LC clips.